The AH-4 is designed for use with Icom HF transceivers. Just push TUNER switch on most modern Icom transceivers and the AH-4 adjusts imediately to the minimum SWR. The AH-4 automatically performs tuning operations for mode, power settings, etc.
Technical Segment
Using the Icom AH-4 with the IC-705
The AH-4 is enclosed in a weatherproof housing and is capable of being permanently installed outdoors. It interfaces to the radio with the coaxial feed line and a 4-conductor control cable. The cable carries the 12 volt power and ground, and the KEY and START control lines. The AH-4 comes with a 16 foot (5 m) control cable that connects to the rear panel of compatible Icom transceiver. A 16 foot (5 m) raw coax cable and two PL-259s are supplied to connect the transceivers antenna output to the AH-4 antenna input. The PL-259s must be soldered on by the user. Click here to view wiring example. ICOM Antenna Tuner Control Cables OPC-136 Be the first to Review this product Antenna Tuner Radio Interface Cable, For ICOM AH-4 to ICOM Transceivers, Four Conductor, 16.4 ft. Ah-4 Control Cable Avast 7.0.1474 License Key Setup Dave Phychodrama Download Forza Horizon 4 Pc Keygen Uniblue Driver Scanner 2019 Arcview Projection Utility Install Singular Live Api Doc Sight Glass Should Look Emptry Outdoor Lights Wedding Ps2 Save Builder.
In this article, FB NEWS Worldwide editors are going to introduce how to use the Icom AH-4 Automatic Antenna Tuner with the IC-705. It is reported that an Icom antenna tuner especially for the IC-705 is being planned for release, but we just wanted to use a wire antenna with the IC-705 “right now.”
Please note that this is not an officially recommended method by Icom.
Pin assignments of the IC-705 TUNER jack
There is a TUNER jack on the right side of the IC-705, and according to the Icom webpage, an antenna tuner will be released in the future that can be connected to it.
Right side of the IC-705
This is a three-conductor stereo jack, and [KEY], [START], and [GND] are assigned sequentially from the tip.
Pin assignment
Connecting the AH-4 to the IC-705
Unlike the IC-7610 or IC-7300, there is no jack especially for the AH-4 on the IC-705. However, we assumed that if we connect the control lines of the AH-4 to the IC-705’s TUNER jack, and separately supply the 13.8 V DC power...the antenna tuner might work well.
When the AH-4 is connected to the IC-7300, the 13.8 V power is supplied from the radio to the AH-4.
When the AH-4 is connected to the IC-705, both the AH-4 and IC-705 must be connected to the same power supply and grounded at the same internal GND terminal.
To connect the AH-4 to the IC-705, connect the three control lines for KEY, START and GND to the tip, ring, and sleeve of a 3.5 mm stereo plug. Connect the fourth power line to a suitable power connector, which is required to supply 13.8 V DC power to the tuner. You can purchase a 3.5 mm stereo plug at a parts shop, but we also recommend trying out a screw-type connector.
Direct wiring with a screw-type connector is convenient for a trial.
Control Cable Inc Baltimore Md
Now, there are two ways to connect the AH-4 to the IC-705.
1. Build a control cable for the AH-4.
2. Build a conversion cable that is connected to the AH-4 supplied cable.
When you chose No.1:
Purchase a 4-conductor shielded cable and build the control cable. One side is for the J2 connector in the AH-4, the other side is for the IC-705 TUNER jack and the DC power supply.
The 4-conductor shielded cable we bought.
When you chose No.2:
To make a conversion cable, buy the necessary spare parts described below. Contact your local distributor for ordering details. Because the AH-4 standard supplied cable is too long for the IC-705, you can cut and shorten it if needed, but we are not responsible for any trouble that may occur.
Required spare parts:
...female, radio side
Component name: 1490R1
Icom component number: 6510001940
...4 pins are required
Component name: 1189TL
Icom component number: 6510007460
Completed conversion cable
Verifying operation
This is a screen capture before we connect the AH-4 to the IC-705. [TUNER] is grayed out.
The IC-705 FUNCTION screen before connecting
Connect both the AH-4 and the IC-705 to the same regulated power supply after turning it OFF. Then turn ON the power supply to power ON the AH-4 first, then push the [POWER] key in the IC-705 to turn ON the IC-705. This sequence is important for the AH-4 to be recognized by the IC-705. Now look at the IC-705 FUNCTION screen again to confirm that [TUNER] is no longer grayed out. Touch and hold [TUNER] for one second to turn it ON.
The IC-705 FUNCTION screen after connected
When tuning is started, the [TUNE] icon blinks red in the upper-left corner of the IC-705 screen. When tuning is complete, the icon stops blinking and is lit white.
Control Cable Assembly
The IC-705 screen after tuning
Hydraulic Control Cable
We look forward to seeing the Icom antenna tuner!
Control Cable For Cars
Now we figured out that we can use the AH-4 connected to the IC-705...but we can’t wait for the official Icom antenna tuner, to bring out the best in the IC-705!
Comments are closed.